WC Cabin with shower, WC Cabin

Sink

Compass, Map plotter, Echo sounder, Autopilot, GPS, VHF Radio

Bimini-Top

Battery charger, Mechanical bilge pump, Shore supply

holding tank

spinnaker, Spinnaker furnishing, mainsail, roller-furling genoa, gennaker

Beneteau First 27 SE delivers fun and modern downwind planing sailing thanks to modern design and building technologies. Families will go cruising, you'll enjoy a fun and exciting day sailing, and she will win trophies on the club races. Interior of this pocket-cruiser can welcome up to 6 persons and offers separated bow-cabin, open space saloon, galley with freshwater, fridge and separated classic marine toilet.Board the ship and have fun!

Covers

- Bimini Top

- Lazy Bag

Electrical Equipment

- Shore Power Inlet

Electronics

- Depthsounder
- Log-Speedometer
- Wind Speed and Direction

- Plotter
- Autopilot
- Compass
- GPS

Inside Equipment

- Manual Bilge Pump

- Marine Head
- Battery Charger

Outside Equipment/Extras

- Solar Panel

Rigging

- Tiller
- Hydraulic Winch

Sails

- Battened Mainsail
- Gennaker/Cruising Spinnaker

- Furling Genoa

CONSTRUCTION:

Hull and deck constructed with Vacuum Infusion of Vinyl ester
resin, foam and Soric GRP sandwich with unidirectional and biaxial
laminates
Hull is reinforced with Infused GRP stringers in the keel and bow
sections
Hull and deck are moulded in single tone off-white,
Deck with high traction non-skid moulded
Carbon fibre beams laminated on keel box and glued to the deck to
support mast compression and keel hydraulic ram
Two transoms hung balanced rudders, built of GRP foam sandwich,
Red chainplates bolted to the main structural bulkhead
Bolts, screws and fittings are all made of stainless marine grade
stainless steel
Faired underwater areas, ready for sanding, epoxy primer and
antifouling application
SWINGING KEEL SYSTEM:

Swinging keel with “elephant leg” lead bulb, main steel structural
element and epoxy GRP enclosure
Laminated areas of the keel are pre-painted with epoxy primer for
easier antifouling treatment
Manually operated hydraulic pump with stainless steel hydraulic ram
built in the carbon fibre mast support
DECK EQUIPMENT:

60 cm high stainless steel pulpit, pushpit and six stanchions painted
in mat black, with double lifelines
Stainless steel bow and stern mooring cleats
Stainless steel chain plates for side shrouds and forestay painted in
mat red
Four Wichard folding pad eyes for lifting straps at mid-two stations,
2x Harken STA15 secondary halyard winches and 2x Harken STA20
jib and gennaker trim primary winches
2x Spinlock winchfeeder on the coachroof
Two rope bags and two winch handle bags, Outils Océans & First
branded
Wide mainsail traveller, installed over the tiller
Carbon tiller with Spinlock EA1200DS tiller extension
Laminated tempered glass windows on both sides of the hull
An opening hatch of 58 cm x 58 cm / 23 x 23 inch for light
ventilation and deck access to the mid-section compartment
An opening hatch of 25,5 cm x 25,5 cm / 10 x 10 inch for front
cabin ventilation
Bow anchor locker with Dyneema J3 staysail attachment point on
the deck
Stern storage compartment cover
Foldable outboard cockpit compartment with two top & one bottom
cover and engine bracket for internal combustion outboard (not
mounted)
Manual bilge pump operated from the cockpit
MAST & RIGGING:

CompoTech mast and boom with two sets of swept-back spreader build in high-quality carbon fibre

Ask us for more information.